- REGIT POS CASH REGISTER ERROR 52 SERIAL
- REGIT POS CASH REGISTER ERROR 52 MANUAL
- REGIT POS CASH REGISTER ERROR 52 SOFTWARE
- REGIT POS CASH REGISTER ERROR 52 CODE
REGIT POS CASH REGISTER ERROR 52 SOFTWARE
Some Windows software keeps the COM port closed all the time and only opens the COM port when trying to send out data. Wait for at least 5 seconds before opening the drawer again. Since the available power from the COM port is very weak, it takes a few seconds for the cash drawer to store up enough energy for kicking out the drawer. The CR3002 draws power from the COM port. To use the CR3000, make sure that the application software keeps the ports open all the time and have the handshake signals DTR and RTS enabled.
REGIT POS CASH REGISTER ERROR 52 SERIAL
It can be opened with any character send to the serial port and can use any communication protocol with any bit rate from 150 bps up to 19.2K bps. Power is drawn from the COM port to open up the drawer. There is no external power supply needed and it connects to the DB25 serial port of the computer directly. The CR3002 is Logic Controls’ unique design “Self Powered” cash drawer. The power comes from the printer in case of CR3000 and from the AC power adapter in case of CR3001. Normally, a cash drawer needs power supplied externally to open the drawer.
REGIT POS CASH REGISTER ERROR 52 MANUAL
Refer to your POS software manual or call your software vendor tech support for the correct format. Some software use comma to separate entries, some just use a blank space to separate entries. Some use 027 or \27 to enter decimal 27, some use 1BH, $1B, or &H1B to enter hexadecimal 1Bh. Note that different POS software use different method for entering the codes. Following are examples for some common printers:
REGIT POS CASH REGISTER ERROR 52 CODE
Refer to your POS printer manual for the correct command code sequences. The control codes depends on model of printer used. Check to see if there are anything (coins or bills) blocking the solenoid at the back from moving freely. If it doesn’t open, use the key to open the drawer. Make sure the lock is in the vertical position and try again. You may need to refer to your software user manual or contact your software supplier for assistance. If this test opened the drawer, go back to your application software and check the port settings for COMx, 9600 baud, no parity, 8 bit data and 1 stop bit, and drawer opening code is Ctrl-G (hex 07). If you get a “Write fault error to COM port”, close any other software that are set to use the same COM port and then try again (check Autoexec.bat file to see if a LPT printer port is redirected to the COM port). If this still does not work, make sure the switches are set to their default settings and that the power supply adapter is working. The drawer should open if you haven’t changed any of the default switch settings inside the drawer. After that, on the next line hold down Ctrl and hit G. At the DOS prompt, enter “MODE COMx 96,n,8,1” (excluding the “” marks x=1 or 2 depending upon which port you are hooked up to). Shell out to the MS-DOS command prompt or restart computer in DOS mode. What are the default DIP switch settings for CR3001?ĭoes the CR3000 series cash drawers come with cables?Ĭan I change the baud rate setting for the cash drawer?Īre Logic Controls cash drawers programmable?Įxit from your application software. Why the CR3000 drawer does not open through my Epson TM-U200 or Citizen CBM1000 receipt printer with the Ctrl-G command code? I tried with the DOS functional test command to open the cash drawer and get a “Write Fault Error”. I could hear a light clicking sound from the drawer each time I try to open with the software but it just doesn’t pop out. However, working with my POS software, it doesn’t work. I tested the CR3002 in DOS mode and it works beautifully.
The CR3002 opens through computer control at first trial but does not open the next time. What is the CR3002 Self Powered Cash Drawer?
What are the control codes for opening a CR3000 printer driven drawer? The cash drawer sounds like it is trying to open, but it doesn’t open. My CR3001 does not open from the SERIAL port through my application software.
0 kommentar(er)
